Boot-probs----->Hardware

ProphetCHRIS

Grand Admiral Special
Mitglied seit
11.05.2001
Beiträge
9.318
Renomée
243
Standort
Taipei
also,

ich habe das KG7 eingebaut, sonst ist alles aus meinem altem system, also da hatte diese probs nicht...

es geht darum:

wenn ich den PC anschalte, denn starten die HDD's nicht, also wird auch nicht gebootet, wenn ich denn nochmal aus mache, und wieder starte, denn geht alles ganz normal......


also nochmal,

MoBo KG7
athlon 1200
hdd's WD und IBM
NT zalman silent 300W

keinerlei scsi...
ist eben erst seitdem ich das KG7 eingebaut habe, mit 300W hat es vorher auch geklappt,

hat jmd nen rat !?  :) :)
 
Hört sich eigentlich nach zu schwachem Netzteil an.
Aber das Zalmann hat auf jeden Fall genug Leistung (erreicht locker ein Enermax 350Watt).

Evtl. zieht das neue Board den gesamten Strom nur von der 3,3V Schiene oder nur von der 5V?
 
Nimm mal ein Programm wie Speedfan und lass dir deine Volts bei Vollast anzeigen.
Vollast kannst du mit CPUBurn z.B. erreichen.
 
Nehme mal an das es sich um das KG7 mit Raid handelt.

Hatte mit meinem Epox 8kta3+ das gleiche Problem mit meiner HDD wenn sie am Raid-Controller (HPT 370) hängt.

PC einschalten Rechner fährt hoch, findet kein Boot System und bleibt stehen. Reset und es funktioniert ohne Probleme.

Erst nachdem ich im Bios auf Boot Device HPT 370 umgestellt hatte, und dann beim hochfahren ins Bios des HPT 370 reinbin, hat es funktioniert.

 
ist nicht das raid  :'( die sache ist ja die, die platten fangen nicht mal an zu laufen, geben keinen ton von sich.

habe das mit dem strom gechecked, nichts auffälliges, were mal das bios durchforsten...
 
sehr sehr komisch. ??? ???

Was sagt das Bios dazu beim ersten einschalten, stehen die dort beide platten drin, wenn nicht, und sie stehen beim zweiten mal drin, würde ich sagen das die einstellung im bios nicht gespeichert werden und somit das board einen macken hat bzw. cmos, oder habe ich jetzt einen denkfehler.

 
Hallo,
wenn die Platten nicht anlaufen, also keinen Strom bekommen bin ich mir ziemlich sicher das es am NT liegt. Etwas anderes kann ich mir nicht vorstellen.

p.s. klemme mal nur deine Bootplatte an, mal sehen ob es dann geht.
 
Nur wenn es am Netzteil liegen soll,

warum funktioniert es beim zweiten Start ??? ???
 
Weil dann die Kondensatoren im Netzteil schon geladen sind und beim Starten der Komponenten zusätzlich noch Strom liefern können, und die Kondensatoren der Komponenten schon geladen sind und keinen Strom mehr ziehen.
 
@gOhAsE

Also nochmal,

für altes system reicht die stromversorgung ohne probleme.

neues motherboard (braucht mehr strom als altes, netzteil mit zu wenig leistung, und das war´s dann.

dann man ja langsam anfangen die ganzen wattangaben der einzelgeräte zu prüfen und dann schauen ob die gesamtleistung ausreicht, na toll.

 
???

Wie soll ich jetzt deinen Post verstehen?

Ich habe dir doch eine Antwort auf deine Frage gegeben?!

Und das Chris´ Problem wahrscheinlich mit dem Netzteil zusammenhängt, stimmt auch?!

Also ich hab das jetzt wirklich nicht verstanden.

???
 
hey,

also, ich habe das ganze jetzt mit nem DRITTEN NT getestet, und wieder das gleiche prob, also muss es doch am Mainboard liegen ODER??

beim zweiten mal geht es immer
 
Tja, dann musst du vielleicht mal die Einstellungen im Bios testen.
Evtl. auch neues Bios aufspielen?

Probier auch mal "Load Fail Safe Defaults" aus!
 
@gOhAsE

war nur noch mal zum Verständnis. ja ich weiss das deutsch war nicht gerade das beste, war ein bisschen in eile geschrieben *lol*

mir will nur nicht in den kopf, wenn bei einem laufenden system (alt), dann 1 komponente tausche, nach tausch probleme auftauchen, es am alten netzteil liegen soll.

Tippe daher immer noch auf das neue Mainboard als Ursache.

Entweder Bios oder Controller vom Board.

Würde daher mal zum Händler gehen und Board tauschen.

Nur würde ich vorher kein neues Bios flashen, sonst sagt der Händler womöglich noch, tja selber schuld, irgend was falsch gemacht. Es ist JA SO UNWAHRSCHEINLICH das ein neues teil gleich kaputt ist. ;)

Die Platten haben ja anscheinend ihre Daten noch, sonst würde es beim zweiten mal nicht klappen.

@[OC-Tweaks]ProphetCHRIS

Wenn der Rechner komplett ausgeschaltet ist (stromlos), und du startest ihn dann, stehen dann die platten im bios drin oder nicht?

PS: Das mit den Boot Problemen ist anscheinen kein Einzelfall


Hier ein Auszug aus

http://www.hardocp.com/reviews/mainboards/abit/kg7/index5.html

Kyle:
Leave it to a [H]ardOCPer to show us the error of our ways! If you read the ABIT KG7-Review you will notice in the conclusion where we talk about boot problems with the board. It seems that our Netgear NIC cards are the culprit. Did we change out our configuration when trying get our board problem free? Yes, we did, but we changed out a FA311 for a FA312 and both cards have the same problem. We removed our NIC and drivers through the control panel option in Win2K and the system booted just fine coming out of Windows and the BIOS settings. This problem does not seem to be isolated to the ABIT KG7 but rather to the AMD 761 chipset. Hopefully we can find more information on this. Here is a thread over at AMDMB that touches on this issue.

Our test boards were not without problem, though.  This review is a week late and with good reason.  The first pre-production KG7 we received would not boot properly and took many tries at powering up the board to even get the BIOS adjustments to take.  We got in touch with ABIT about this a couple weeks ago and started working through it together.  The second KG7 they sent us, the one used for all these benchmark numbers, also had a boot problem, but it was not near as severe as the first.  It too would not reboot itself after exiting Win2K.  This about doubled the time needed to get the data for the review.  We have worked with ABIT on this for a week now and they have not been able to reproduce our problem in their labs.  At this point I do not know whether the fault lies with the board, our equipment, or our testing know-how.  We are going to return both boards to ABIT for further testing at their facilities in Taiwan so they can make sure a problem is not being overlooked.  I do not think this will be an issue with retail boards, but it is still a problem we encountered so we need to mention it to you.  




 
Gab's da nicht mal irgendwelche Probs mit einem Chipsatz, der sich genau in dem von Chris beschriebenen Prob äusserte!?
 
@chris

hier ist noch eine seite für dein board wenn probleme auftauchen

http://fae.abit.com.tw/eng/faq/mb/kg7.htm

 
Zurück
Oben Unten