"Fehlermeldung" von SpeedFan?

WhiteStar

Cadet
Mitglied seit
08.02.2006
Beiträge
48
Renomée
0
Ich hab vor kurzem mein System neu aufgesetzt. Das Tool SpeedFan liefert mir beim Start folgende Statusmeldung:

Win9x:NO 64Bit:NO GiveIO:YES SpeedFan:YES
I/O properly initialized
Linked ISA BUS at $0290
Linked VIA VT8237 SMBUS at $0400
Found nVidia GeForce FX 5200
Linked nVidiaI2C0 SMBUS at $3D403E3F
Linked nVidiaI2C1 SMBUS at $3D403637
Linked nVidiaI2C2 SMBUS at $3D405051
Scanning ISA BUS at $0290...
Winbond W83697HF (ID=$60) found on ISA at $290
SuperIO Chip=Winbond W83697HF
Scanning VIA SMBus at $0400...
Address $31 appears to be WRITE ONLY...
Scanning I2CNVidia SMBus at $3D403E3F...
Scanning I2CNVidia SMBus at $3D403637...
Scanning I2CNVidia SMBus at $3D405051...
SMART Enabled for drive 0
Found ST3160021A (160,0GB)
SMART Enabled for drive 1
Found SAMSUNG SP2004C (200,0GB)
Bad Attributes Checksum ($A0)
Bad Thresholds Checksum ($D5)

End of detection
Error loading event -->
CfgVersion=01.0001
EventsVersion=01.0001
Loaded 0 events

Kann mir jemand was zu dem fett-geschrieben Teil sagen? Ich kann mich nicht erinnern dies früher schon mal gelesen zu haben. An meiner Hardwarekonfiguration hab ich nichts geändert, nur Windows neu aufgesetzt.

Wäre dankbar für hilfreiche Antworten.
 
bei mir sieht die Stelle so aus:

Found ST3200822A (200,0GB)
Found ACPI temperature (27,0C)
End of detection

deshalb denke ich das es ein Problem mit dem ACPI gibt.

Ich würde mal im Gerätemanager nachschauen.
evtl. Chipsatztreiber neu installieren wenn das nicht hilft
BS neu machen da es noch weitere Auswirkungen auf das Powermanagment geben könnte.
 
Naja, die Fehlermeldungen kommen direkt nach den Festplatten bzw. nach der SMART-Aktivierung.

Und da es bei SMART Attribute und Thresholds gibt, sieht es eher nach einem Problem mit der Festplatte aus bzw. es kommt zu Fehlern beim Auslesen der SMART-Werte (Prüfsummen stimmen nicht).

Versuche mal, mit einem anderen Programm die SMART-Werte der Festplatten auszulesen.

MFG,
kreuzritter2001
 
Hab ich mal mit Everest gemacht. Nachfolgend die Ergebnisse:

ST3160021A (5JS0QL2G)

ID Eigenschaften-Beschreibung Grenzwert Wert Schlechtester Wert Daten Status
01 Raw Read Error Rate 6 65 58 90391964 OK: Wert ist normal
03 Spin Up Time 0 96 96 0 OK: Keine Fehler
04 Start/Stop Count 20 100 100 348 OK: Wert ist normal
05 Reallocated Sector Count 36 100 100 0 OK: Wert ist normal
07 Seek Error Rate 30 84 60 330914611 OK: Wert ist normal
09 Power-On Time Count 0 84 84 14801 OK: Keine Fehler
0A Spin Retry Count 97 100 100 0 OK: Wert ist normal
0C Power Cycle Count 20 99 99 1026 OK: Wert ist normal
C2 Temperature 0 33 53 33 OK: Keine Fehler
C3 Hardware ECC Recovered 0 65 58 90391964 OK: Keine Fehler
C5 Current Pending Sector Count 0 100 100 0 OK: Keine Fehler
C6 Off-Line Uncorrectable Sector Count 0 100 100 0 OK: Keine Fehler
C7 Ultra ATA CRC Error Rate 0 200 200 0 OK: Keine Fehler
C8 Write Error Rate 0 100 253 0 OK: Keine Fehler
CA <Anbieterspezifisch> 0 100 253 0 OK: Keine Fehler

SAMSUNG SP2004C (S07GJ10YB12615)
ID Eigenschaften-Beschreibung Grenzwert Wert Schlechtester Wert Daten Status
01 Raw Read Error Rate 51 100 100 1 OK: Wert ist normal
03 Spin Up Time 25 100 100 5952 OK: Wert ist normal
04 Start/Stop Count 0 100 100 150 OK: Keine Fehler
05 Reallocated Sector Count 10 253 253 0 OK: Wert ist normal
07 Seek Error Rate 51 253 253 0 OK: Wert ist normal
08 Seek Time Performance 15 253 253 0 OK: Wert ist normal
09 Power-On Time Count 0 100 100 3119 OK: Keine Fehler
0A Spin Retry Count 51 253 253 0 OK: Wert ist normal
0B Calibration Retry Count 0 253 2 0 OK: Keine Fehler
0C Power Cycle Count 0 100 100 150 OK: Keine Fehler
BE <Anbieterspezifisch> 0 157 142 27 OK: Keine Fehler
C2 Temperature 0 157 142 27 OK: Keine Fehler
C3 Hardware ECC Recovered 0 100 100 6564483 OK: Keine Fehler
C4 Reallocation Event Count 0 253 253 0 OK: Keine Fehler
C5 Current Pending Sector Count 0 253 253 0 OK: Keine Fehler
C6 Off-Line Uncorrectable Sector Count 0 253 253 0 OK: Keine Fehler
C7 Ultra ATA CRC Error Rate 0 200 200 0 OK: Keine Fehler
C8 Write Error Rate 0 100 100 0 OK: Keine Fehler
C9 <Anbieterspezifisch> 0 100 100 0 OK: Keine Fehler
CA <Anbieterspezifisch> 0 253 253 0 OK: Keine Fehler


Alternativ hab ich dazu noch den in SpeedFan intergrierten "Perform an in-depth online analysis of this hard disk" benutzt

Auch hier mal die Ergebnisse:

Your hard disk is a SAMSUNG SP2004C with firmware VM100-33.
The average temperature for this hard disk is 32C (MIN=22C MAX=44C) and yours is 27C.
Your hard disk's S.M.A.R.T. attributes are now being analyzed and a full report about the reliability, health and status of your hard disk is generated:
Your hard disk is not below any attribute threshold. This is good.
Your hard disk was never below any attribute threshold. This is good.
All of the attributes of your hard disk have normal values. This is good.

The overall fitness for this drive is 90%.
The overall performance for this drive is 90%.

Your hard disk is a ST3160021A with firmware 3.04.
The average temperature for this hard disk is 39C (MIN=26C MAX=51C) and yours is 33C.
Your hard disk's S.M.A.R.T. attributes are now being analyzed and a full report about the reliability, health and status of your hard disk is generated:
Your hard disk is not below any attribute threshold. This is good.
Your hard disk was never below any attribute threshold. This is good.

NOTE: not all warnings are reflected on fitness and performance overall values as relevancy is based upon the settings from the hard disk manufacturer who is the best entity deputed to define such relationships.

NOTE : your hard disk Power On Hours Count attribute current value (84) is below the normal range (85 - 100) reported for your specific hard disk model. Basically your hard disk was powered on for more than the maximum time the average user did. This means that either all of the reports collected are from hard disks that were not powered on for too long (this is realistic for recent models) or that your hard disk is becoming old. Usually this is not considered as a pre-failure advisory, but you should check whether you want to replace the hardware or keep an eye on its performances over time.


The overall fitness for this drive is 90%.
The overall performance for this drive is 98%.
 
Hm...ich benutze noch Version 4.27, die von Dir genannte Funktion kenne ich noch gar nicht, steht aber im Changelog zu Version 4.28.

4.28
- added IN-DEPTH HARD DISK ONLINE ANALYSIS tool
- added centralized INTERNET configuration tab in CONFIG dialog
- added support for NForce410
- added support for new video cards
- added Temperature Sensor Type, BJT Offset and Gain support for Fintek F75375S in CONFIGURE / ADVANCED (on Asus V9999 you might need to set BJT OFFSET from 174 to 202)
- SMART overall indicators are computed using a more advanced strategy
- updated the help file
- properly fixed byte swapped HDD model names

Da diese Funktion sehr neu ist, denke ich, daß Deine Festplatten in Ordnung sind und es sich nur um einen Auslesefehler handelt (auch wegen der "more advanced strategy"). Deine Festplatten sind laut den SMART-Werten gut gekühlt und vollkommen in Ordnung, insofern würde ich die Fehlermeldung von Speedfan ignorieren. Vielleicht tritt der Fehler bei Version 4.29 nicht mehr auf... ;)

Wenn Du auf Nummer sicher gehen willst, könntest Du die Festplatten jeweils noch mit dem herstellerspezifischen Testprogramm durchchecken. :)

MFG,
kreuzritter2001
 
Zurück
Oben Unten