S.M.A.R.T Werte ok?
- Ersteller Shooty76
- Erstellt am
Ich habe 2 Platten, wo zumindest eine bei größeren Dateien zum entpacken oftmals spinnt.
Hier die SMART Werte
DTemp version: 1.00 build 34 (RC8)
Started under WinNT kernel, version 5.1.2600
Number of processors: 1
Processor type: x86 Family 15 Model 47 Stepping 0, ~1804 MHz
-------------------------[Device information]-------------------------
Physical drive: 1
Compatiblity: ATA/ATAPI-5
Model: WDC WD800BB-32CCB0
Firmware revision: 22.04A22
Serial number: WD-WMA9P1114279
Disk capacity: 74.53 Gb (156301488 sectors)
Buffer size: 2048 Kb
Identify information CRC: Ok
----------------------[Device S.M.A.R.T. status]----------------------
Attribute Value Thresh Raw Flags
----------------------------------------------------------------------
Raw read error rate 200 51 000000000000h CR OC ER
Spin up time 107 21 000000001541h CR OC PR
Start/stop count 99 40 00000000063Dh OC EC SP
Reallocated sector count 200 140 000000000000h CR OC EC SP
Seek error rate 200 51 000000000000h CR OC ER
Power-on time count 78 0 0000000040E7h OC EC SP
Spin up retry count 100 51 000000000000h CR OC EC
Recalibration retries 100 51 000000000000h CR OC EC
Device power cycle count 99 0 0000000005FBh OC EC SP
Reallocation event count 200 0 000000000000h OC EC SP
Current pending sector count 200 0 000000000000h OC EC
Off-line uncorrectable sector count 200 0 000000000000h OC EC
Ultra ATA CRC error rate 200 0 000000000000h OC ER
Write error rate 200 51 000000000000h CR ER
----------------------------------------------------------------------
CR-life critical OC-online collection PR-performance related
ER-error rate EC-event count SP-self preserving
Attributes CRC: Ok Thresholds CRC: Ok
--------------------------[Device features]---------------------------
Maximal transfer block in sectors: 16, current: 16
Transfer modes:
PIO: 0-4
Single word DMA: not supported
Multi word DMA: 0-2
UltraDMA: 0-5
Current transfer mode: Ultra DMA-5
Drive features:
LBA supported, 48 bit addressing not supported
SMART supported, enabled
Device status: Ok
Attributes structure revision: 10h
Thresholds structure revision: 10h
Pre-power mode attributes autosave supported
Attributes autosave after event supported
Temperature check capability not found
SMART error logging not supported
SMART self test not supported
Offline data collection supported
Suspend offline collection after new host command
Offline read scanning supported
Offline self test supported
Security mode supported, disabled
Master password revision code: unknown
Security locked: no
Security frozen: no
Security count expired: no
Security erase time: unknown
Enchanced security erase not supported
Security level: high
Write cache supported, enabled
Read look ahead supported, enabled
Host protected area supported, enabled
Microcode downloading supported
Power management supported, enabled
Advanced power management not supported
Automatic acoustic management supported, disabled
Recommended AAM value: 80h (minimum acoustic emanation level)
Current AAM value: FEh (maximum performance)
Media serial number not supported
Und hier die zweite:
Physical drive: 0
Compatiblity: ATA/ATAPI-7 minor version 001Eh
Model: SAMSUNG SP1604N
Firmware revision: TM100-23
Serial number: 0651J1FW621464
Disk capacity: 128.00 Gb (268435455 sectors)
Buffer size: 2048 Kb
Identify information CRC: Ok
----------------------[Device S.M.A.R.T. status]----------------------
Attribute Value Thresh Raw Flags
----------------------------------------------------------------------
Raw read error rate 100 51 000000000000h CR OC ER
Spin up time 44 0 000000002300h CR OC PR
Start/stop count 99 0 0000000005AEh OC EC SP
Reallocated sector count 253 10 000000000000h CR OC EC SP
Seek error rate 253 51 000000000000h CR OC ER
Seek time performance 253 0 000000000000h PR SP
Power-on time count 99 0 0000000F4D90h OC EC SP
Spin up retry count 253 49 000000000000h CR OC EC
Device power cycle count 100 0 0000000002F6h OC EC SP
Temperature 151 0 00000000001Dh OC SP
Hardware ECC recovered 100 0 00000F12BA40h OC ER
Reallocation event count 253 0 000000000000h OC EC
Current pending sector count 253 10 000000000000h CR OC EC SP
Off-line uncorrectable sector count 253 10 000000000000h CR EC SP
Ultra ATA CRC error rate 100 0 000000000002h OC ER
Write error rate 100 51 000000000000h CR OC ER
Attribute 201 100 51 000000000000h CR OC ER
----------------------------------------------------------------------
CR-life critical OC-online collection PR-performance related
ER-error rate EC-event count SP-self preserving
Attributes CRC: Ok Thresholds CRC: Ok
--------------------------[Device features]---------------------------
Maximal transfer block in sectors: 16, current: 16
Transfer modes:
PIO: 0-4
Single word DMA: not supported
Multi word DMA: 0-2
UltraDMA: 0-6
Current transfer mode: Ultra DMA-6
Drive features:
LBA supported, 48 bit addressing supported
SMART supported, enabled
Device status: Ok
Attributes structure revision: 10h
Thresholds structure revision: 10h
Pre-power mode attributes autosave supported
Attributes autosave after event supported
Temperature check capability found
SMART error logging supported
Log directory not supported
Summary SMART error log not supported
Comprehensive SMART error log not supported
SMART self-test error log not supported
SMART self test supported
Offline data collection supported
Suspend offline collection after new host command
Offline read scanning supported
Offline self test supported
Security mode supported, disabled
Master password revision code: unknown
Security locked: no
Security frozen: no
Security count expired: no
Security erase time: 96 min.
Enchanced security erase supported, erase time 48
Security level: high
Write cache supported, enabled
Read look ahead supported, enabled
Host protected area supported, enabled
Microcode downloading supported
Power management supported, enabled
Advanced power management not supported
Automatic acoustic management supported, enabled
Recommended AAM value: FEh (maximum performance)
Current AAM value: FEh (maximum performance)
Media serial number not supported
Danke
Hier die SMART Werte
DTemp version: 1.00 build 34 (RC8)
Started under WinNT kernel, version 5.1.2600
Number of processors: 1
Processor type: x86 Family 15 Model 47 Stepping 0, ~1804 MHz
-------------------------[Device information]-------------------------
Physical drive: 1
Compatiblity: ATA/ATAPI-5
Model: WDC WD800BB-32CCB0
Firmware revision: 22.04A22
Serial number: WD-WMA9P1114279
Disk capacity: 74.53 Gb (156301488 sectors)
Buffer size: 2048 Kb
Identify information CRC: Ok
----------------------[Device S.M.A.R.T. status]----------------------
Attribute Value Thresh Raw Flags
----------------------------------------------------------------------
Raw read error rate 200 51 000000000000h CR OC ER
Spin up time 107 21 000000001541h CR OC PR
Start/stop count 99 40 00000000063Dh OC EC SP
Reallocated sector count 200 140 000000000000h CR OC EC SP
Seek error rate 200 51 000000000000h CR OC ER
Power-on time count 78 0 0000000040E7h OC EC SP
Spin up retry count 100 51 000000000000h CR OC EC
Recalibration retries 100 51 000000000000h CR OC EC
Device power cycle count 99 0 0000000005FBh OC EC SP
Reallocation event count 200 0 000000000000h OC EC SP
Current pending sector count 200 0 000000000000h OC EC
Off-line uncorrectable sector count 200 0 000000000000h OC EC
Ultra ATA CRC error rate 200 0 000000000000h OC ER
Write error rate 200 51 000000000000h CR ER
----------------------------------------------------------------------
CR-life critical OC-online collection PR-performance related
ER-error rate EC-event count SP-self preserving
Attributes CRC: Ok Thresholds CRC: Ok
--------------------------[Device features]---------------------------
Maximal transfer block in sectors: 16, current: 16
Transfer modes:
PIO: 0-4
Single word DMA: not supported
Multi word DMA: 0-2
UltraDMA: 0-5
Current transfer mode: Ultra DMA-5
Drive features:
LBA supported, 48 bit addressing not supported
SMART supported, enabled
Device status: Ok
Attributes structure revision: 10h
Thresholds structure revision: 10h
Pre-power mode attributes autosave supported
Attributes autosave after event supported
Temperature check capability not found
SMART error logging not supported
SMART self test not supported
Offline data collection supported
Suspend offline collection after new host command
Offline read scanning supported
Offline self test supported
Security mode supported, disabled
Master password revision code: unknown
Security locked: no
Security frozen: no
Security count expired: no
Security erase time: unknown
Enchanced security erase not supported
Security level: high
Write cache supported, enabled
Read look ahead supported, enabled
Host protected area supported, enabled
Microcode downloading supported
Power management supported, enabled
Advanced power management not supported
Automatic acoustic management supported, disabled
Recommended AAM value: 80h (minimum acoustic emanation level)
Current AAM value: FEh (maximum performance)
Media serial number not supported
Und hier die zweite:
Physical drive: 0
Compatiblity: ATA/ATAPI-7 minor version 001Eh
Model: SAMSUNG SP1604N
Firmware revision: TM100-23
Serial number: 0651J1FW621464
Disk capacity: 128.00 Gb (268435455 sectors)
Buffer size: 2048 Kb
Identify information CRC: Ok
----------------------[Device S.M.A.R.T. status]----------------------
Attribute Value Thresh Raw Flags
----------------------------------------------------------------------
Raw read error rate 100 51 000000000000h CR OC ER
Spin up time 44 0 000000002300h CR OC PR
Start/stop count 99 0 0000000005AEh OC EC SP
Reallocated sector count 253 10 000000000000h CR OC EC SP
Seek error rate 253 51 000000000000h CR OC ER
Seek time performance 253 0 000000000000h PR SP
Power-on time count 99 0 0000000F4D90h OC EC SP
Spin up retry count 253 49 000000000000h CR OC EC
Device power cycle count 100 0 0000000002F6h OC EC SP
Temperature 151 0 00000000001Dh OC SP
Hardware ECC recovered 100 0 00000F12BA40h OC ER
Reallocation event count 253 0 000000000000h OC EC
Current pending sector count 253 10 000000000000h CR OC EC SP
Off-line uncorrectable sector count 253 10 000000000000h CR EC SP
Ultra ATA CRC error rate 100 0 000000000002h OC ER
Write error rate 100 51 000000000000h CR OC ER
Attribute 201 100 51 000000000000h CR OC ER
----------------------------------------------------------------------
CR-life critical OC-online collection PR-performance related
ER-error rate EC-event count SP-self preserving
Attributes CRC: Ok Thresholds CRC: Ok
--------------------------[Device features]---------------------------
Maximal transfer block in sectors: 16, current: 16
Transfer modes:
PIO: 0-4
Single word DMA: not supported
Multi word DMA: 0-2
UltraDMA: 0-6
Current transfer mode: Ultra DMA-6
Drive features:
LBA supported, 48 bit addressing supported
SMART supported, enabled
Device status: Ok
Attributes structure revision: 10h
Thresholds structure revision: 10h
Pre-power mode attributes autosave supported
Attributes autosave after event supported
Temperature check capability found
SMART error logging supported
Log directory not supported
Summary SMART error log not supported
Comprehensive SMART error log not supported
SMART self-test error log not supported
SMART self test supported
Offline data collection supported
Suspend offline collection after new host command
Offline read scanning supported
Offline self test supported
Security mode supported, disabled
Master password revision code: unknown
Security locked: no
Security frozen: no
Security count expired: no
Security erase time: 96 min.
Enchanced security erase supported, erase time 48
Security level: high
Write cache supported, enabled
Read look ahead supported, enabled
Host protected area supported, enabled
Microcode downloading supported
Power management supported, enabled
Advanced power management not supported
Automatic acoustic management supported, enabled
Recommended AAM value: FEh (maximum performance)
Current AAM value: FEh (maximum performance)
Media serial number not supported
Danke
gruenmuckel
Grand Admiral Special
Scheinen beide perfekt in Ordnung zu sein.
Keine defekten Sektoren, keine Sektoren unter Beobachtung, nicht zu warm, also alles paletti!
Keine defekten Sektoren, keine Sektoren unter Beobachtung, nicht zu warm, also alles paletti!
gruenmuckel
Grand Admiral Special
Tja, irgendwo auf dem Weg von Platte zu Platte gibts da ein Problem...
Teste mal deinen Speicher mit Memtest oder Prime95 im Torture Test.
CPU mal auf Standard takten.
Teste mal deinen Speicher mit Memtest oder Prime95 im Torture Test.
CPU mal auf Standard takten.
gruenmuckel
Grand Admiral Special
Im Prinzip an allem auf dem Weg von Platte zum Kabel, durch das Kabel in den Chipsatz, CPU, RAM, und wieder zurück, u.U. auch durch den PCI-Bus falls der SATA-Controller da dran hängt.Shooty76 schrieb:
Dann wären da noch kaputte Treiber, Mondphasen usw...
Also, womit hast du den Speicher getestet und wie lange?
Schau auch mal in diesen Thread, das klingt deinem Problem sehr ähnlich!
Zuletzt bearbeitet:
Also ich hab Prime nun 8h ohne Fehlöer durchlaufen lassen. Also nehme ich jetzt mal sicher an, dass der RAM ok ist.
Aber bei jeder größeren Datei, die ich entpacke hab ich nen CRC Fehler.
Festplatten hab ich auch mal geprüft, wird kein Fehler angezeigt.
System:
Athlon 3000 (nicht übertaktet)
Abit AX8 3rd Eye
Platten: 1. WD 80GB IDE
2. Samsung 1604 SP 160 GB IDE (ich hab die Western Digital als Bootdisk mit Win XP an Port 1 als Master, die Samsung ebenfalls an Port 1 als Slave)
2 x 512 MB Infineon RAM Double Sided (könnte es vielleicht wegen double sided Probleme geben?)
HIS 800XL Radeon
Soundblaster Audigy
Tagan 480W
Nix ist übertaktet!
Ich hab kein Plan mehr was ich och testen soll. Treiber etc. sind auch alles die aktuellen. Die Option mit dem EXT-P2P Timing gibts bei mir nicht unter Integrated PEripherals im BIOS. Der fehler macht mich echt wahnsinnig, wäre sau cool, wenn mir noch wer helfen könnte.
Danke schonmal im voraus
Aber bei jeder größeren Datei, die ich entpacke hab ich nen CRC Fehler.
Festplatten hab ich auch mal geprüft, wird kein Fehler angezeigt.
System:
Athlon 3000 (nicht übertaktet)
Abit AX8 3rd Eye
Platten: 1. WD 80GB IDE
2. Samsung 1604 SP 160 GB IDE (ich hab die Western Digital als Bootdisk mit Win XP an Port 1 als Master, die Samsung ebenfalls an Port 1 als Slave)
2 x 512 MB Infineon RAM Double Sided (könnte es vielleicht wegen double sided Probleme geben?)
HIS 800XL Radeon
Soundblaster Audigy
Tagan 480W
Nix ist übertaktet!
Ich hab kein Plan mehr was ich och testen soll. Treiber etc. sind auch alles die aktuellen. Die Option mit dem EXT-P2P Timing gibts bei mir nicht unter Integrated PEripherals im BIOS. Der fehler macht mich echt wahnsinnig, wäre sau cool, wenn mir noch wer helfen könnte.
Danke schonmal im voraus
